Critical Heat Flux for Downward Facing Boiling on a Coated Hemispherical Surface

An experimental study was performed to investigate the effect of surface coating on the critical heat flux for downward facing boiling on the outer surface of a hemispherical vessel. Steady-state boiling experiments were conducted in the subscale boundary layer boiling (SBLB) facility using test vessels with metallic microporous coatings to obtain the local boiling curves and the local critical heat flux (CHF) limits. Similar heat transfer performance was observed for microporous aluminum and microporous copper coatings. When compared to the corresponding data without coatings, the boiling curves for the coated vessels were found to shift upward and to the right. This meant that the CHF limit was higher with surface coating and that the minimum film boiling temperatures were located at higher wall superheats. In particular, the microporous coatings were found to enhance the local CHF values appreciably at all angular locations explored in the experiments. Results of the present study showed that the microporous aluminum coating was very durable. Even after many cycles of steady state boiling, the vessel coating remained rather intact, with no apparent changes in color or structure. Although similar heat transfer performance was observed for microporous copper coatings, the latter were found to be much less durable and tended to degrade after several cycles of boiling.     

Configuration Design Sensitivity Analysis of Kinematic Responses of Mechanical Systems∗

Abstract

A continuum-based configuration design sensitivity analysis method is presented for kinematically driven mechanical systems. Configuration design variable for mechanical systems are defined. The 3-1-3 Euler angle is used as the orientation design variable. The reassembly process for a mechanical system after a configuration design change is eliminated by imposing kinematic admissibility conditions of the velocity field. The direct differentiation method is used to derive design sensitivity equations. Numerical examples are presented to demonstrate the validity and effectiveness of the proposed method.     

Photovoltaic devices using semiconducting polymers containing head‐to‐tail‐structured bithiophene,pyrene, and benzothiadiazole derivatives

An alternating copolymer composed of heal‐to‐tail‐structured 3,4′‐dihexyl‐2,2′‐bithiophene (DHBT) and pyrene units [poly(DHBT‐alt‐PYR)] was synthesized using a Stille coupling reaction for use in photovoltaic devices as a p‐type donor. For the reduction of the bandgap energy of poly(DHBT‐alt‐PYR), 4,7‐bis(3′‐hexyl‐2,2′‐bithiophen‐5‐yl)benzo[c][1,2,5]thiadiazole (BHBTBT) units were introduced into the polymer. Poly(DHBT‐co‐PYR‐co‐BHBTBT)s were synthesized using the same polymerization reaction. The synthesized polymers were soluble in common organic solvents and formed smooth thin films after spin casting. The optical bandgap energies of the polymers were obtained from the onset absorption wavelengths. The measured optical bandgap energy of poly(DHBT‐alt‐PYR) was 2.47 eV. As the BHBTBT content in the ter‐polymers increased, the optical bandgap energies of the resulting polymers decreased. The bandgap energies of poly(50DHBT‐co‐40PYR‐co‐10BHBTBT) and poly(50DHBT‐co‐20PYR‐co‐30BHBTBT) were 1.84 and 1.73 eV, respectively. Photovoltaic devices were fabricated with a typical sandwich structure of ITO/PEDOT:PSS/active layer/LiF/Al using the polymers as electron donors and [6,6]‐phenyl C₇₁‐butyric acid methyl ester as the electron acceptor. The device using poly(50DHBT‐co‐20PYR‐co‐30BHBTBT) showed the best performance among the fabricated devices, with an open‐circuit voltage, short‐circuit current, fill factor, and maximum power conversion efficiency of 0.68 V, 5.54 mA/cm², 0.35, and 1.31%, respectively. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Molecular dynamics simulation study on graphene-nanoribbon-resonators tuned by adjusting axial strain

A tunable graphene-nanoribbon (GNR)-resonator was investigated via classical molecular dynamics simulations. Resonance frequencies increased with increasing externally applied gate-force and axial-strain, and could be tuned above several hundred GHz. Tunable resonance frequencies achieved from the gate force were higher than those achieved from the axial-strain. The operating frequencies of GNR-resonators without axial-strain or with small axial-strains were most widely tuned by the gate, and almost linearly increased with increasing mean deflection. As the axial strain increased, the tunable ranges of the GNR-resonators were exponentially decreased, although the operating frequencies increased. GNR-resonators without axial-strain could be applied to wide-range-tuners, whereas GNR-resonators with high axial-strain could be applied to high-frequency-fine-tuners.     

Structure and transmittance behavior of sol–gel silica nanoparticles synthesized using pH-stable alkanolamines

Journal of Sol-Gel Science and Technology - Although sol–gel silica nanoparticles are widely used in academic and industrial applications, only a few studies have focused on amine catalysts...     

Simplifying patterning process of ZnO nanowires by one step development and etching process

We present herein a simple protocol of growing a patterned ZnO nanowire by etching of ZnO seed layer in the tetramethyl ammonium hydroxide (TMAH) solution. The ZnO seed layer was fabricated by sol–gel method using zinc acetate solution and patterned by using photolithographic method. Patterned ZnO seed layer as etched in the TMAH solution, followed by growth of ZnO nanowires by hydrothermal method. Remarkable point of present ZnO seed layer patterning is that development of UV-exposed photoresist and etching of ZnO seed layer is subsequently processed in aqueous TMAH solution without interruption. The grown ZnO nanowires were analyzed using XRD patterns to exhibit high purity and degree of crystallinity, and showed very good pattern fidelity.